List of machinery installed in our company

TURNING Lathe 8 ‘ - 9 ’ bed with 1200 mm turning facility. 01 no. DRILLING 1 1/2 “ dia. Capacity radial drilling m/c 02 nos. ROLLING Plate Bending m/c 20 mm thk. x 2500 mm Width. 01 no. CUTTING     A) Hacksaw m/c - 10 “ dia capacity 01 no. B ) Gas cutting set 02 nos. C ) Gas Cutting “ PUG “ m/c 01 no. D ) Plasma Cutting Unit 02 nos. WELDING        A) Welding Rectifier - 600 A 04 nos. B) Advani make MIG Welding Machine 01 nos. C) Welding Transformer ( Portable ) 200 A 01 no. D) Welding Generator K-320 01 no. E) Welding Rectifier 800 A 01 no. F) Argon Arc Welding High Frequency Unit Suitable for S.S. / Alu. work & Root - Run for piping . 02 nos. G) Forced Air Gauging Torch ( Advani make ) 01 no. GRINDING   A) Pedestal Grinder 14 “ dia. 2 H.P. 01 no. B) Angle, Portable & Pneumatic Grinders 16 nos. PNEUMATIC TOOLING   A) Pneumatic Straight Grinder IEC make 01 no. B) Visu Pneumatic weld flux chipper Model SHT.42 4200 B.P.M. 01 no. TUBE EXPANDER “ POWER MASTER “ make electronic Tube Expander 01 no. TOOLING Electrical Portable Drilling m/c , Sander , Sand - o - flux for polishing S.S. 04 nos. HANDLING     7.5 & 5 Tons Capacity H.O.T. with access over Complete Workplace . 02 nos. 1. LONGITUDINAL TRAVEL 90 FEET 2. CROSS TRAVEL 36 FEET 3. MAX. HOOK LEVEL 22 FEET COMPRESSOR 40 CFM for Pneumatic Tools & Pad Testing . 02 nos

List of Testing Equipments installed at works

• Tong Tester for AC / DC current & Voltage Measurement.
• Digital Vernier.
• ‘ D’ Meter for Thickness Measurement of Ferrous & Non-Ferrous Metals up to 50 mm thk.
• Analog Vernier.
• Poldy Hardness Tester.
• Paint thk. Tester. (Elco meter)
• Templates for “ V” Preparation Checking.
• Templates for Fillet Weld Check.
• Templates for Shell Profile Checking. (D / 4 Templates)
• Measuring Tapes (3 Mtr. / 15 Mtr.)
• Measuring Scales (1 Mtr. / 3 Mtr.)

Note - For Sr. No. 7, 8 & 9 the mentioned Templates are covered under Calibration status & are inspected periodically for correctness.

We at our works carry out following tests regularly & Work Instructions are developed for the same to carryout the tests effectively.

For Destructive testing & Non-destructive testing, we are sub-contracting the activities to our Approved sub-contractors.

List of Approved Sub-contractors for DT / NDT are as mentioned below.

Name of Vendor / Subcontractor Address Item / Service Elca Quality Systems & Calibrations Pvt. Ltd. S. No.232/2, Pune-Nasik Road, Bhosari, Pune – 411 039. D.T.Testing-Plates, Pipe Bars etc. Heat Fabs Block No.T-183, M.I.D.C., Bhosari, Pune-Nasik Road, Pune-411 026. D.T.Testing-Plates, Pipe Bars etc. Quality NDT Services BG A-1/3, Bhosari General Block, Near Post Office, M.I.D.C., Bhosari, Pune-411 026. NDT Services Sonal Industrial Services Kushanai S.No.17/3, Lane No.5, Madhuban, Sangvi, Pune – 411 027 NDT Services